Refurbished by the manufacturer - The item has normal signs of use, e.g. minor scratches, stains or damaged outer box. The product is fully functional and the silver electrodes are unused!
Refurbished by the manufacturer - The product has normal signs of use, e.g. minor scratches, stains or slight damage. The product is fully functional and the silver electrodes are unused!
With the silver generator Ionic-Pulser® Standard S, amateurs and professionals alike can produce the purest colloidal silver up to a concentration of 200 ppm and more themselves.
Generator with automatic water control for the production of standardized silver suspensions
Regardless of the temperature and quality of the water used, uniform quantities of silver are always dispensed.
The intelligent electronics automatically adjust to the electrical conductivity of the water, so that concentrations of up to 200 ppm and more are possible with high accuracy and optimum particle size. Tests by several independent laboratories confirm this information.
- Very easy handling
- Precise concentrations
Deviations less than +/- 5%
- Any concentration possible with any amount of water
(up to 1 liter and more)
- Production also possible with multiple distilled water without additives
Scope of delivery:
- 1 Ionic-Pulser® Standard S with electronic control according to the Ionic-Pulser® system for precise silver concentrations, up to 46 volt electrode voltage
- 1 power supply unit, custom-made 33V AC voltage - 100-240V, also suitable for countries with 110V mains voltage!
- 1 pair of original silver electrodes MED plus with specific degree of hardness, fine silver content at least 99.99%, dimensions: 2.70 x 82 mm, sufficient for over 120 liters (at 25 ppm), manufactured by a company certified in accordance with the Medical Devices Act
-1 detailed instruction manual with table for determining the silver concentration
- 24 months manufacturer's warranty
Two Ionic-Pulser® Standard S devices were tested by several independent laboratories, including ICP analysis* in accordance with DIN EN ISO 11885 and analytical ultracentrifugation. All results corresponded exactly to the values specified by the manufacturer and were confirmed by Prof. Dr. med. R. Werner and Dr. med. Zyganow, Institut für Energie-Medizinische Systeme e.V. (EMS Berlin), among others.
*Iductively
Coupled Plasma Atomic Emission Spectrometry
Description
The silver generator
Ionic-Pulser® Standard S guarantees a constant silver release independent of the type of water and proportional to the production time (VarioPlus in operating mode A). You can use a table to determine the exact concentration.
Technology
A great advantage of the integrated intelligent electronics is the
automatic adjustment to the conductivity of the water, so that standardized suspensions
(up to 200ppm and more) can be produced with very high
accuracy of the concentration laboratory-tested and optimal particle size.
This means that the devices are primarily designed for water with the lowest conductivity and are therefore able to produce the highest quality colloidal silver even with aqua bidest (i.e. double distilled water).
The technical implementation takes place by generating a pulsating direct voltage with comparatively high power, which is superimposed with alternating voltage components. The optimized performance is made possible by the enclosed plug-in power supply with 33 V at the output and the electronics integrated in the device, which supplies approx. 50 V to the electrodes. Furthermore, the high quality of the silver electrodes is decisive for the quality of the finished solution. These have a
fine silver content of at least 99.99% with a high material density.
Measurements have shown that the particle size in the fresh solution is significantly smaller than 7 nm. This means, among other things, that the so-called
Tyndall effect only becomes visible after approx. 2-3 days.
In order to achieve a
long service life for the devices, mechanical components such as switches, regulators and the like have been deliberately omitted. The complicated electronics are 100% protected against moisture by a synthetic resin encapsulation. The housing is a special design with antistatic properties.
Accessories
The sophisticated technology enables the production of colloidal silver in precise concentrations even with aqua bidest, which is hardly conductive. Therefore,
no additives are required for these devices.
Temperature and water control
The intelligent electronics with
automatic water control and
standardized, linear silver release make the Ionic-Pulser® independent of water temperature and quality.
Nevertheless, distilled (demineralized) water that has been heated before use should always be used. Our distillation devices are recommended for production.
Standardized silver delivery
The electronics ensure a linear silver release, which together leads to extremely accurate and reproducible results.
Degree of purity
The fine silver content of the MED Plus electrodes is at least 99.99%. A very high material density is achieved through a special rolling process, resulting in particularly small particle sizes*.
Operation
The operation of the devices is very simple:
- heat the appropriate amount of water and pour into a drinking glass,
- insert the silver rods into the appliance,
- place the appliance on the glass and
- connect the power supply unit.
Using the enclosed table, you can see how long the Ionic-Pulser® needs to reach the desired concentration.
Shelf life
Colloidal silver can be used for many months, but its charge decreases continuously and should therefore be used as fresh as possible.
Storage
In order to keep the silver solution in its optimum condition for a long time, the following must be observed:
- Do not place in electromagnetic fields (next to electric stove, TV and stereo etc.).
- Do not store in the refrigerator, but in a cool, dark place.
- Do not store in plastic or metal containers, but only in dark glass bottles.
- Do not dilute to change the concentration.
If you are not sure about the concentration, we recommend 25ppm for most applications at the beginning.
As so-called electrode sludge normally forms on the electrodes, these should be cleaned with a kitchen towel after each run.
Then pour the solution through a paper filter (coffee filter) to keep any foreign particles out of the solution.
All devices of the Ionic-Pulser® system are maintenance-free.
*Only original electrodes
FREE Delivery on orders over 99€*
Prices Include All EU Duties & Tax
60 day refund or exchange
Delivery Across Europe
Delivery Across Europe
60 day refund
